TDMA Wireless Bridge
Home  > Products  > TDMA Wireless Bridge  > 

1km HDMI Video Sender HDMI Transmitter And Receiver Indoor Short Range WIFI WDS Wireless Bridge Mode

1km HDMI Video Sender HDMI Transmitter And Receiver Indoor Short Range WIFI WDS Wireless Bridge Mode

-Adopt a high performance AR9531 chip, the maximum rate can reach 300Mbps, outdoor transmission distance of 1km.

-Support point-to-point, or point-to-multipoint transmission mode.

-Unique antenna, RF amplifier, and low-noise receiver design to ensure long-distance transmission.

-TDMA technology can maximize the use of bandwidth resources to better support point-to-multipoint data transmission.

-Support POE mode power supply, and the power supply is more convenient and reliable.

-Can be remotely controlled and managed via a webpage for easy configuration.

Get Latest Price
Get the latest price
Quantity Needed:

1km HDMI Video Sender HDMI Transmitter And Receiver Indoor Short Range WIFI WDS Wireless Bridge Mode is very suitable for apartment complex、parks、factories. Easy and high-speed wireless transmission of surveillance video data.

Installation and fixation of wireless bridge equipment.

When installing a wireless bridge, the first step is to fix the wireless bridge device bracket. Whether the bracket is stable or not directly affects the stability of the signal transmission. During installation, since the surface of the bracket is relatively smooth, it is necessary for us to put a layer of rubber ring on the bracket and make close contact between the U-shaped clip code. In order to prevent the infiltration of outdoor rainwater for a long time, when the surface of the bracket is rusted, the contact between the U-shaped clip and the bracket is loose. In addition, the transmitter and receiver signal antennas of the wireless bridge must be aligned to ensure stable signal reception.

Model selection of POE power supply box

At present, there are two main types of POEs recommended for use, the modular POE with external DC power input and the regulated POE with AC 220V voltage input through the internal integrated transformer. It should be noted that no matter which POE is used, its interface definition is unified. The network port marked "DATA IN" on the POE can be connected to network devices such as network cameras, switches, computers, etc., marked with "P + DATA OUT" The network port can only be connected to the wireless bridge device. If it is connected incorrectly, it will cause the device to burn out, so be careful.

Product Model


Network Protocol

Management tools to automatically search for IP addresses;

Web management

Wireless Transmission Distance

1000 meters

Support Capacity

10 channel 2M stream IPC

Networking Method

Point to point

Wireless Standards

IEEE 802.11b/g/n(2*2 MIMO 300 Mbps)

Working Frequency


Antenna Angle

Half-power beamwidth:65° ± 5°

Reception Sensitivity

87 ± 2dB @11Mbps

Maximum Air Interface 

Transmission Rate

≤ 300 Mbps

Network Interface Type

1 RJ45 ,10/100 Mbps self-adaptive

Channel Width

20/40 MHz

Working Scenes

Apartment complex/ Parks/ Factories

Security Mode


Security Mechanisms

Hide the wireless network name

Network Mode


Management Approach


System Logs

System log information printing

Software Updates

Web,Client Updates

Power Input


Power Consumption


Overall Dimensions

200mm × 110mm × 53 mm


300 g (single device itself only)

Working Temperature


Working Humidity

5% RH~95% RH Non-condensing

Storage Temperature


Storage Humidity

5% RH~95% RH Non-condensing

Installation Method

Wall-mounted, pole type

Power Supply Method

12-24V DC 1 A power adapter + PoE power supply

wireless bridge

wireless hdmi transmitter and receiver

wireless hdmi transmitter

Chat Online 编辑模式下无法使用
Leave Your Message inputting...
Hello, thank you for your attention to amplitec .which model are you interesting ? Please leave a message online or send email to info@amplitec.cn. Our working hours are from am8:30 to pm18:00 Beijing time. We will reply to you in the first time during this period!