Home  > Products  > Mobile Signal Repeater  > Wide Band Repeater  >  17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna
17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna
17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna
  • 17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna
  • 17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna
  • 17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna
  • 17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna
  • 17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna

17 dBm Single Wide Band Cell Phone Repeater with Built-in Antenna

 Product Feature:

 


* Whole set design, users don't need to purchase accessories

* With built-in antenna, reduce the difficulty of installation

* Extensible external antenna, increase coverage

* Isolation detection and alarm function, prompt the quality of user installation, 

   and guide the user to install

* Input and output signal strength instructions, easy to understand the installation effect

* Sleep mode function, when the coverage area is without mobile phone, the uplink 

   will be turned off to reduce the interference to the base station

* Signal indicator light auto-extinguishing function, after the device turns on 10 minutes, 

   the signal strength indicator light will be automatically extinguished to reduce light 

   pollution and energy consumption

* MOQ: 10 Pcs

 

     Amplitec C17F series cell phone signal booster has outdoor and indoor units.  They are connected with 20 meters LMR100 small diameter cable. Because the diameter of the LMR100 cable is only 3mm, compared with 5D-FB or 1/2 cable, LMR100 cable is much easier to install. But the  signal loss of the 20 meter LMR100 cable will be up to 23dB, so the outdoor unit of the booster is also designed with amplify circuit. The power supply needed by the outdoor unit will be taken from the RF IN port of the indoor unit and transmitted through  LMR100 cable . The outdoor unit is designed with 40 dB gain, can make up for the signal attenuation of LMR100 cable, so the gain of the whole set can still reach to 65dB.

     The outdoor and indoor units are both with built-in antenna design.It can meet the users' signal enhancement needs in most cases. When the strength of outdoor base station signal is below -70 dBm, a Yagi antenna can be added to the outdoor unit to enhance the strength of the base station signal. And a service antenna can be added to the indoor unit to expand indoor coverage.

     C17F series mobile signal repeater is usable for home, office and other small places to make 3G or 4G  mobile signal coverage.

 

Model Frequency
 

Model

Frequency range

Uplink

Downlink

 

C17F Single Band

EGSM

880-915MHz

925-960MHz

CDMA/ LTE 5

824-849MHz

869-894MHz

WCDMA/ LTE 1

1920-1980MHz

2110-2170MHz

 


Electrical Specification  

Item

Uplink

Downlink

Output Power

17±2 dBm

17±2 dBm

Gain

68±2 dB

72±2 dB

ALC Active 10dB

≤2 dB

≤2 dB

Ripple

≤8dB

≤8dB

Max. Input Power Without Damage

-10 dBm

-10 dBm

Intermodulation Products

≤-30 dBm

≤ -36 dBc

Spurious Emission

9KHz~1GHz

≤ -36 dBm

≤ -36 dBm

1GHz~12.75GHz

≤ -30 dBm

≤ -30 dBm

VSWR

≤3

---

Time Delay

≤1.5 μs

≤1.5 μs

LED indicator

Run

ON

Green

OFF

OFF

ISO

Normal

Green

Not Enough

1.ISO LED light Red;

2.Downlink input signal LED light blinks;

3.Downlink output signal LED light blinks.

Downlink Input

OFF

Input power ≤ -95±2dBm

One Light On

-94±2dBm ≤ Input power ≤ -85±2dBm

Two Lights On

-84±2dBm ≤ Input power ≤ -75±2dBm

Three Lights On

-74±2dBm ≤ Input power ≤ -65±2dBm

Four Lights On

Input power ≥ -64±2dBm

Downlink Output

OFF

Input power ≤ -19±2dBm

One Light On

-18±2dBm ≤ Output power ≤ -8±2dBm

Two Lights On

-7±2dBm ≤ Output power ≤ 3±2dBm

Three Lights On

4±2dBm ≤ Output power ≤ 14±2dBm

Four Lights On

Input power≥15±2dBm

Working Status Requirement

Working Normally

10 mins before starting up

According to the normal working status indication

10 mins after starting up

1.Input signal indicator, output signal indicator and ISO indicator will be OFF;

2. RUN indicator turns Green

ISO Not

Enough

10 mins before starting up

Run ISO Not Enough indication accordingly

10 mins after starting up

Run ISO Not Enough indication accordingly

Cut cable between

Main Unit and Remote Unit

1. Downlink Input Signal indicator blinks;

2. ISO and RUN indicator turn Green;

3.Downlink Output Signal indicator OFF.

Power Supply

DC: 24V

Power Consumption

<5W

Interface

RF IN

Downlink signal input port and Remote Unit 24V power supply port

RF OUT

Downlink output extension port

Environment Condition

IP40

Operating Temperature

-10℃~+55℃


Product Message

Loading verification code...

Please complete verification first

社媒暂无评论
Contact